When traveling with empty forklifts The forks should be in what position?
Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back. Use caution when carrying a load on an uneven surface; it creates a tip-over hazard.
How low should the forks generally be when traveling without a load?
Travel with forks as low as possible from the floor and tilted back (usually within 10-15 cm (4 to 6 inches) above the floor).
When traveling on a level surface the forks should be raised?
When traveling on a level surface, you should raise the forks about 12 inches with or without a load. Dock plates should be visually checked by the lift truck operator. Use of the safety built restraint system is required only when you are traveling with a load.
How high should forks be when driving forklift OSHA?
The forks will always be carried as low as possible, consistent with safe operations, usually 4 inches off the floor.
How far should you stand from a forklift?
The safe traveling distance between forklifts is approximately three truck lengths, or about a time-lapse of three seconds when passing the same point. More specifically, it’s about 20 feet between forklifts. The three-second rule is the same for automobiles on the road and is just as important for forklifts.
What steps should you do every time you park a forklift?
Lower the forks to the floor when parking the forklift. Make sure that the forks touch the ground when you are leaving. Apply the parking brake when it is the idle position. All operational controls of the truck must be in the neutral position before the driver alight the forklift compartment.
What should you do every time you park a forklift?
Parking Safety Rules
- Always try to find a level surface to park on.
- Lower forks, or the forklift attachment, all the way to the ground.
- Put the gear into neutral.
- Make sure the wheels are straight.
- Set the parking brake every time you park the forklift.
- Turn off the engine before dismounting the forklift.
When driving with an empty forklift forks should be kept 18 to 24 inches off the ground?
When driving a empty forklift,forks should be kept 18 to 24 inches off the ground. The safest way to cross curbs and railroad tracks is at an angle. When working with pallets ,forks should be positioned as widely apart a possible.
What is the minimum safe distance to drive behind another forklift?
Falling distance of an object from a pallet or 15 feet, 5 Feet both sides, 5 Feet Rear of Forklift. do so (ALL CLEAR). Do not pass under the forks while in operation.
How far apart are the forks on a forklift?
For handling pallets, ideally your forks should be spaced equally apart center to the carriage/backrest, around 10 inches out from each side. But really there is no exact measurement; the best rule is to space them just a bit less from as wide as you can have them for the pallets/loads you will be handling.
How many feet do you use to drive a forklift?
You should have two feet and a hand or two hands and a foot in contact with the vehicle at all times. Make sure your arms and legs are inside the vehicle at all times, and always use the operator’s restraint system.
How many forklift lengths should you maintain between your forklift and another forklift traveling in front of you?
A safe distance shall be maintained approximately three truck lengths from the truck ahead, and the truck shall be kept under control at all times. 1910.178(n)(4) – The driver shall be required to slow down and sound the horn at cross aisles and other locations where vision is obstructed.
How tall should Forks be on a forklift?
It is also dangerous when you reach an incline or slope, that is why when traveling in slope, drive the forklift in reverse. In a typical warehouse setup with an even floor surface, the forks should be above the ground at a height of 5 to 10 centimeter. This height is the same as it needs to go through a wooden pallet.
Why does an empty forklift have better stability?
In 75% of cases of side tipover the forklift is empty. As noted above this is because adding load increases stability in respect of side tipover. The principal factors affecting side tipover are the centre of mass of the empty forklift, the speed of the forklift, and the radius of a turn.
What’s the best way to drive a forklift?
When traveling with a load, always make sure to tilt the mast of the forklift backward so that the load will firmly place against the backrest to make it more secure during transport. By doing this, you move the center of gravity towards to rear of the forklift making it more secure when traveling. Distribute the weight of the load properly.
Why are forklifts more likely to tip sideways?
However the centre of mass at the same time is moving away from the two other tipping axis. So the Forklift becomes more stable in respect of tipping sideways. Hence forklifts are much more likely to tip sideways when empty – 75% of these incidents occur when the forklift is empty. And they are more likely to tip forward when loaded.