Categories :

What is port profile in Nexus?

What is port profile in Nexus?

Port profile is a mechanism used in NEXUS family of switches for simplifying the configuration of interfaces. We can assign a port profile to multiple interfaces and provide them all the same configuration. One can configure Ethernet or vEthernet port profiles to which Ethernet or vEthernet interfaces can be assigned.

How do I enable ports on my Nexus?

You can make all ports Layer 2 ports using the setup script or by entering the system default switchport command. See the Cisco Nexus 9000 Series NX-OS Fundamentals Configuration Guide for information about using the setup script. To configure the port as a Layer 2 port using the CLI, use the switchport command.

What is a port profile?

Port profiles provide a convenient way of provisioning interfaces on switches. You can either use predefined port profiles, or you can define your own custom port profile. After you create a Port profile, you can assign it to interfaces on one or more switches, including aggregated interfaces.

How do I configure Nexus switch?

Power up the new Nexus switch and connect to the console port using a serial cable. The switch will take several minutes to boot. The initial configuration wizard starts automatically. Use the information you worked out with your team or with the customer to complete the wizard.

What is link debounce?

The port debounce time is the amount of time that an interface waits to notify the supervisor of a link going down. During this time, the interface waits to see if the link comes back up.

How do you remove a car with no negotiation?

negotiate auto To enable the autonegotiation protocol to configure the speed, duplex, and automatic flow-control of the Gigabit Ethernet interface, use the negotiate command in interface configuration mode. To disable automatic negotiation, use the no negotiate auto command.

How do I change the default port for Nexus?

To change the NEXUS default port:

  1. Stop Nexus.
  2. Edit the nexus. properties file. In this example, it is located in the Talend installation\tac\Artifact-Repository-Nexus-V2. 14.3-02\nexus-2.14. 3-02\conf folder.
  3. Find application-port=8081 and change 8081 to XXXX, that is, add any open port.
  4. Save the file.
  5. Start Nexus.

What is the default port of Nexus repository?

port 8081
By default, the repository manager listens on port 8081. You can change this port, by changing the value in the $NEXUS_HOME/conf/nexus. properties file shown in Contents of conf/nexus.

How do I configure a switch?

How to configure Cisco switch?

  1. Initial command prompt “Switch>” appears on the screen.
  2. Type “enable” next to it and press “Enter”.
  3. This will take you into the “EXEC” mode, also known as the Global Configuration mode.
  4. Go into configure mode using configure terminal.
  5. Enter the configuration commands one per line.

How do I save settings on Nexus 5k?

Saving the Running Configuration to the Startup Configuration

  1. show running-config.
  2. copy running-config startup-config.

What is Cisco link debounce?

Usage Guidelines. The port debounce time is the amount of time that an interface waits to notify the supervisor of a link going down. During this time, the interface waits to see if the link comes back up.

What is carrier delay Cisco?

carrier-delay. To delay the processing of hardware link down notifications, use the carrier-delay command in interface configuration mode. Note. The carrier-delay command is active only when both up and down are configured from the host. The range of carrier-delay on access port of CRS is 0 to 2147483648 msec.

How to configure Cisco Nexus 5500 port profiles?

Configuring an interface is simplified by using an “inherit” command to apply much of the needed configuration using a port profile. NX-OS makes sure that the commands in the port profile are applied to the interface. Enforcing standard interface configurations.

What do port profiles do on Nexus switches?

Port Profiles is a feature of Nexus switches, which allow a template of configuration to apply to a group of ports. This is similar to interface macros in Catalyst IOS.

How many ports can a Cisco Nexus 5596 have?

On a Nexus 5596 running NX-OS 5.2 (1)N1 (1), the limit is 512 interfaces, though that number can go as high as 1024 using the “max-ports” command. When a port profile is deleted, the interfaces that inherited the port profile lose the configuration commands belonging to the deleted port profile.

Do you need to create a port profile?

Network engineers must create specific port profiles types to match specific interface types. Ethernet, VLAN, port-channel, and Virtual Ethernet interface types are supported. Once created, port profiles must be enabled before they will be active.