What is code c0710?
The steering angle sensor receives a 12 V reference voltage from the Electronic Brake Control Module (EBCM). The EBCM receives high speed controller area network (CAN) message inputs from the steering angle sensor identifying the position and direction of the steering wheel rotation.
What happens when a steering angle sensor goes bad?
When the sensor is faulty, misaligned, or damaged, the information it reads and sends to the vehicle’s on board computer is inaccurate. In most cases, this will lead to a “loose” condition in the steering wheel, where the amount of steering input you provide is not reciprocated by the action of the vehicle.
Where is the steering wheel position sensor located?
steering column
A steering position sensor (also called a steering angle sensor) may not be the most exciting part of a car, but along with brakes and the suspension system, it’s an important part as far as safety goes. It’s a donut-shaped sensor located in the steering column under the dash in GM vehicle.
How do you check steering wheel position sensor?
To test the SAS, you have to back probe a connector that is typically under the steering column. As the steering wheel is turned 360 degrees, the SAS produces a signal that toggles between 0 and 5 volts. As the wheel is turned lock-to-lock, the voltage will reach 5 volts three times and 0 volts three times.
How do you change a steering angle sensor?
Replacing the Sensor in 15 Easy Steps
- Disconnect the negative battery cable.
- Turn the wheel slightly to the left.
- Locate the sensor.
- Locate the bolt just under the sensor.
- Using a socket, loosen, but do not remove the nut on the bolt.
- With the steering wheel, position the front wheels straight ahead.
How do I reset my electronic power steering?
Turn ignition switch OFF, and turn ignition switch ON. The EPS indicator comes on for about 6 seconds. Within 4 seconds of turning the switch ON, while the EPS indicator is on, turn the steering wheel 45° to left from straight ahead driving position, and hold steering wheel in position until EPS indicator goes off.
Does ABS sensor affect steering?
Electronic stability control improves vehicle handling and steering. To accomplish this, the ABS computer monitors changes in vehicle speed, momentum, steering and acceleration. This information is provided by a number of sensors, including the wheel speed sensors.
Does traction control affect steering?
Traction control works by applying individual wheel braking and throttle to maintain traction under acceleration, but unlike ESC, it is not designed to aid in steering.
What is the steering position sensor?
A Critical Safety Component The Steering Angle Sensor is an important part of a vehicle’s safety system. It transmits the steering wheel’s rate of turn, wheel angle, and other important data to the specific vehicle’s computer. If there is a fault in the signal, the computer can disable the vehicle’s stability control.
What does steering position mean?
The steering angle is defined as the angle between the front of the vehicle and the steered wheel direction as shown in Figure 11.
How much does it cost to diagnose GMC c0710 code?
The cost to diagnose the C0710 GMC code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
What is usually the problem that causes the c0710 code on?
The C0710 code on a 2001 C5 and what is usually done to repair it… What is usually the problem… What is usually the problem that causes the C0710 code on a 2001 C5 and what is usually done to repair it? Steering Position Signal Malfunction
How to diagnose a c0710 Chevrolet steering position signal?
Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. How much do you know about cars? What does this mean? The cost of diagnosing the C0710 CHEVROLET code is 1.0 hour of labor.
What to do about service stability c0710 c0455?
If all those items check out, proceed with the recommended GM fix. an intermittent C0710, C0455 Service Stability condition. The advice is to remove the connector to the SWPS and use a nylon brush to apply dielectric grease to the terminals inside the connector and the SWPS.